Re: [MV] MV gauge part needed

From: Rick v100 (rickv100@yahoo.com)
Date: Tue Jul 19 2005 - 04:37:18 PDT

Next message: Mark W: "6.2L Diesel"
Previous message: Rick v100: "MV gauge part needed"
Next in thread: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: Rick v100: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: david gudmunsen: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: J. Wiehe: "Re: [MV] MV gauge part needed"
Maybe reply: david gudmunsen: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: bruce C. Beattie: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: Thomas M McHugh: "Re: [MV] MV gauge part needed"
Maybe reply: Ryan Gill: "Re: [MV] MV gauge part needed"
Maybe reply: noel shelley: "Re: [MV] MV gauge part needed"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

Should read clamps.

Thanks,
Rick

--- Rick v100 <rickv100@yahoo.com> wrote:

> Anyone happen to have any extra gauge camps? These
> are
> the sheet metal parts you attach to the back of the
> gauge for holding them in.
>
> I need one for a oil pressure gauge.
>
> Thanks,
> Rick
>
>
> ===Mil-Veh is a member-supported mailing list===
> To unsubscribe, send e-mail to:
> <mil-veh-off@mil-veh.org>
> To switch to the DIGEST mode, send e-mail to
> <mil-veh-digest@mil-veh.org>
> To reach a human, contact <ack@mil-veh.org>
>

Next message: Mark W: "6.2L Diesel"
Previous message: Rick v100: "MV gauge part needed"
Next in thread: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: Rick v100: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: david gudmunsen: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: J. Wiehe: "Re: [MV] MV gauge part needed"
Maybe reply: david gudmunsen: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: bruce C. Beattie: "Re: [MV] MV gauge part needed"
Maybe reply: MYDEUCEANDWILLYS@aol.com: "Re: [MV] MV gauge part needed"
Maybe reply: m35products: "Re: [MV] MV gauge part needed"
Maybe reply: Thomas M McHugh: "Re: [MV] MV gauge part needed"
Maybe reply: Ryan Gill: "Re: [MV] MV gauge part needed"
Maybe reply: noel shelley: "Re: [MV] MV gauge part needed"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Fri Oct 28 2005 - 23:22:18 PDT